The short answer
City of Phoenix water already carried 172–302 mg/L of hardness in 2025, and evaporation leaves those minerals behind. That's why pool tile lines crust white, swamp cooler pads scale up and misting nozzles clog. The main defenses are a working cooler bleed-off, balanced pool chemistry and regular descaling. A home softener usually isn't the fix outdoors: pools need some calcium, and these systems are normally plumbed separately.
Key takeaways
- City of Phoenix water measured 172–302 mg/L (10–17.6 gpg) of hardness and 464–716 mg/L of TDS in 2025, before any evaporation.
- Evaporation removes water but leaves minerals, so pools, spas and swamp coolers get harder over time unless water is drained or bled off.
- Illinois Extension: without bleed-off, mineral deposits on cooler pads reduce evaporation efficiency. Check monthly and never add bleach or bromine.
- Pools need some calcium, and very soft water tends to be corrosive (WHO). Don't fill a pool with softened water without a pool pro checking the balance.
- In ASU scale tests, Colorado River (CAP) water formed about 1.5 times and Scottsdale groundwater about 2.25 times the scale of Tempe tap water.
On this page
- Why is hard water such a problem outdoors in Phoenix?
- What does hard water do to a pool or spa?
- Should you fill a pool or spa with softened water?
- Why do swamp cooler pads crust up so fast?
- How do you maintain a swamp cooler in hard water?
- Should a swamp cooler run on softened water?
- Why do misting systems clog, and how do you clean them?
- Where does a home water softener fit?
Most hard-water advice is written for places where hard water means a spotty shower door. In the Phoenix Valley, a lot of the water a home uses ends up outdoors, in pools, spas, swamp coolers and patio misters, and all of them work by letting water evaporate. That turns already-hard water into much harder water. Here’s what’s happening, what helps, and where a home softener does and doesn’t belong.
Why is hard water such a problem outdoors in Phoenix?
It starts with the fill water. The City of Phoenix’s 2025 Water Quality Report lists hardness of 172–302 mg/L, or 10–17.6 grains per gallon (gpg), and total dissolved solids (TDS) of 464–716 mg/L. Penn State Extension classes anything above 10.5 gpg as “very hard.” Other Valley utilities publish their own numbers, which you can compare on our Phoenix-area water hardness page.
Then evaporation takes over. When water evaporates, the minerals don’t go with it. Illinois Extension puts it plainly for evaporative coolers: “salts and mineral concentration builds as the water is evaporated.” A pool losing water to summer heat, or a cooler pad running all day, keeps getting refilled with hard water while the old minerals stay behind.
Source water matters too. In Arizona State University tests of untreated water under heated scaling conditions, Colorado River (CAP) water formed about 1.5 times and Scottsdale groundwater about 2.25 times the scale of Tempe tap water. Two homes a few miles apart can see very different crusting. Our guide to TDS in Phoenix water explains why dissolved solids matter alongside hardness.
What does hard water do to a pool or spa?
The most visible sign is the white crust along the tile line. That’s mostly calcium carbonate, left at the waterline as water evaporates and the level moves up and down. Over time, calcium in the pool also climbs, because every top-up adds more hardness and evaporation never takes any away.
Pool water has to be balanced, not just low in calcium. The common tool is the Langelier Saturation Index (LSI), which University of Georgia Extension describes as the standard scale-and-corrosion index; values near zero mean balanced water. Water that’s too high in calcium, especially at high pH, tends to scale. Water that’s too low tends to be aggressive. The WHO notes that unstabilized soft water is corrosive, and pool trade guidance says low-calcium water can attack plaster.
Pool industry standards publish a target calcium hardness range. We couldn’t verify the exact figures from the standard itself, so we’re not quoting numbers here. Your pool professional or a good test kit will give you the target for your surface. When calcium gets too high, partial draining and refilling is the usual fix.
Spas follow the same chemistry in a smaller, hotter body of water. Heat makes calcium carbonate less soluble, so scale forms faster at hot-tub temperatures.
Should you fill a pool or spa with softened water?
Generally not without testing first. Pools need some calcium to stay balanced, and fully softened water has had its calcium removed. Softening also adds sodium, about 8 mg/L for every grain of hardness removed according to Nebraska Extension. At City of Phoenix hardness, that’s roughly 80–140 mg/L of added sodium. Our page on sodium in softened water has the details.
In most homes the question doesn’t come up, because pools and their auto-fill lines are usually plumbed separately from a home softener. If you’re thinking about changing that, ask your pool pro first. They’re balancing the water week to week and will know how a change in fill water affects your surface and equipment.
Why do swamp cooler pads crust up so fast?
An evaporative cooler is an evaporation machine. Water trickles over the pads, part of it evaporates to cool the air, and the minerals stay on the pads and in the sump. With hard fill water, scale builds quickly.
Illinois Extension’s guidance is written for agricultural cooling pads, but the chemistry is the same in a home unit. Without bleed-off, mineral deposits “reduce evaporation efficiency,” so a crusty pad cools less. The answer isn’t a stronger cleaner. It’s removing concentrated water before it can deposit.
How do you maintain a swamp cooler in hard water?
Adapted from Illinois Extension’s evaporative pad guidance:
- Make sure the bleed-off is working. Most coolers have a bleed-off line or valve that continuously drains a little of the concentrated sump water. If it’s clogged, kinked or shut off, minerals build up much faster.
- Check the pads monthly during cooling season for white crust or hard deposits.
- Increase bleed-off if you see deposits. Illinois Extension: “Reduce bleed off for softer water and increase for harder water.” Phoenix water is in the “increase” category.
- Never add bleach (chlorine) or bromine to the cooler. Illinois Extension says it shortens pad life.
- Use the right descaler. Organic-acid descalers are acceptable for pads. Follow the product label, and don’t combine it with any other cleaner.
- Replace or wash pads seasonally once they’re crusted.
- Clean the sump and water distribution lines when you service the pads, so loose scale doesn’t clog the distribution tubes.
Should a swamp cooler run on softened water?
The evidence here is thin, so we’ll be direct about what we know. Illinois Extension’s guidance assumes some coolers run on softer water and simply says those need less bleed-off. We found no independent study testing home swamp coolers on softened water.
What we do know: evaporation concentrates whatever is in the water, and that includes the sodium a softener adds. In most homes, coolers are fed from a separate line that isn’t on the softener, the same way irrigation usually isn’t (see our plants and landscaping page for why softened water stays out of the yard). If you’re considering a change, ask the technician who services your cooler.
Why do misting systems clog, and how do you clean them?
Patio misters push water through very small nozzles, and each fine droplet that evaporates near the nozzle leaves a little mineral behind. Indoors, the parallel is the low-flow showerhead: in industry-funded Battelle testing at 26 gpg, all five hard-water low-flow showerheads clogged.
To keep misters running:
- Soak clogged nozzles in white vinegar, then rinse and reinstall. Vinegar dissolves carbonate scale. Follow the mister manufacturer’s instructions if they differ.
- Never use vinegar alongside bleach. Health Canada warns that bleach reacts with acids to release toxic gases.
- Flush the lines at the start of the season.
- Know what an inline filter does. A basic sediment or carbon filter catches particles or reduces chlorine. It doesn’t remove dissolved calcium and magnesium.
Crust on patio glass and outdoor fixtures comes off the same way as indoors; see our hard water stain removal guide.
Where does a home water softener fit?
Indoors. A whole-home water softener removes calcium and magnesium from the water feeding your fixtures, appliances and water heater. Pools, coolers, misters and irrigation are usually left off the softener on purpose, and EPA WaterSense notes that outdoor water use may not require softened water at all. Outdoors, bleed-off, pool balance and regular descaling do the work.
What we can help with outdoors is information. Our free in-home water test measures hardness, TDS, chlorine and pH at your tap, which gives your pool pro or cooler technician real numbers for your fill water. If an indoor softener makes sense too, you’ll get an upfront written quote. You can book the free test here.
Frequently asked questions
What calcium hardness should my pool have?
Pool industry standards publish a target calcium hardness range and balance it with the Langelier Saturation Index. We couldn't verify the exact figures from the standard itself, so use the target from your pool professional or test kit. Too little calcium makes water aggressive to plaster; too much, especially with high pH, scales.
Why does my pool water keep getting harder?
Evaporation takes water out and leaves the minerals behind, and every top-up with hard fill water adds more. Partial draining and refilling is the usual way pool pros bring it back down.
Can I use bleach to clean swamp cooler pads?
No. Illinois Extension says never to add bleach (chlorine) or bromine to an evaporative cooler, because it shortens pad life. Use a pad cleaner or a mild organic-acid descaler made for coolers.
How do I get the white line off my pool tile?
That line is mostly calcium carbonate concentrated by evaporation at the waterline. Use a descaler made for pool tile and follow its label, and ask your pool pro to check the water balance so it doesn't come straight back.
Will a water softener protect my swamp cooler or pool?
Not directly. Coolers and pools are usually plumbed separately from a home softener, and softened fill water can throw off pool chemistry. A softener protects your indoor plumbing, fixtures and water heater; outdoors, bleed-off, balance and descaling do the work. See our stain removal guide for fixtures.
Sources
- 2025 Water Quality Report. City of Phoenix Water Services (2025). www.phoenix.gov/waterqualityreport
- Evaporative Cooling Pads: Maintenance for Longer Life. University of Illinois Extension (2019). extension.illinois.edu/blogs/ag-engineering-update/2019-06-11-evaporat…
- Evaluation of Alternatives to Domestic Ion Exchange Water Softeners (WateReuse Project 08-06). Arizona State University / WateReuse Research Foundation (c. 2011). watertectucson.com/wp-content/uploads/2020/04/SCALE-STOP-ASU-STUDY.pdf
- Corrosive or Scaling Water, C858-9. University of Georgia Extension (2026). fieldreport.caes.uga.edu/publications/C858-9/corrosive-or-scaling-wate…
- Hardness in Drinking-water. World Health Organization (2011). cdn.who.int/media/docs/default-source/wash-documents/wash-chemicals/ha…
- Water Softening. Penn State Extension (2025). extension.psu.edu/water-softening
- Drinking Water Treatment: Water Softening (Ion Exchange), G1274. Nebraska Extension (2016). extensionpubs.unl.edu/publication/g1274/html/view
- Battelle Finds Water Softeners Aid Energy Efficiency, Appliance Life (WQRF-funded). Contractor magazine (2010). www.contractormag.com/green/article/20872711/battelle-finds-water-soft…
- Reduce your risk of toxic gases: never mix bleach with other cleaning products. Health Canada. recalls-rappels.canada.ca/en/alert-recall/reduce-your-risk-toxic-gases…
- Hardness of Water. USGS Water Science School. www.usgs.gov/special-topics/water-science-school/science/hardness-wate…
- WaterSense Technical Reference: Water Softeners. U.S. EPA WaterSense (2023). www.epa.gov/system/files/documents/2023-08/ws-homes-TRM-9-WaterSoftene…
This page is general information from a water treatment company, not medical or veterinary advice. Where we cite research we link the original source. Found an error? Email andrew@cactuswatersolution.com and we'll fix it.